General Electric Washer Dryer Combo Parts
- Search your model number to find:
- Genuine OEM parts guaranteed to fit
- Free manuals and guides
- Repair instructions and videos
Popular General Electric Washer Dryer Combo Parts
Your Price
$13.17
In Stock
General Electric Washer Dryer Combo Drum Glide Bearing - White (Sold individually)
PartSelect Number PS4704230
Manufacturer Part Number WE3M51
This drum glide bearing is an authentic OEM replacement part that is compatible with dryers. It is white in color and made of highly durable plastic. The bearing allows the drum to rotate smoothly and dry your clothes thoroughly and evenly. It keeps the drum stable and protects it from excessive friction damage. Over time, the bearing may wear down or break due to normal aging or wear from repeated use. If the bearing is no longer able to support the drum, you will likely notice unusually loud grinding or squeaking noises from the dryer. You may also notice increased drying times due to poor drum rotation. Inspect all the bearings on your dryer, as they tend to wear down at the same time. Each drum glide bearing is sold individually.
Fixes these symptoms
- Marks left on clothes
- Noisy
- See more...
Installation Instructions
Maurice from MINERAL SPGS, AR
Dryer was making noise
Took the top and front end of the dryer off. Took the old slider spacers off and installed the new ones. I replaced all four of them even though only two was bad. While I had the dryer open I decided to use my shop vac to clean up the lint that had accumulated there. Replaced the front and the lid plugged it up, hit the start no noise just like new.
Read more...
Your Price
$27.87
In Stock
General Electric Washer Dryer Combo Direct Drive Motor Coupling
First take off the water pump by removing the two clips that hold it in place. Place a shallow pan under the pump to catch the water that is in the pump and hoses. Open the hose clamps with a pair of pliers or channel locks (better) and slide the hoses off of the water pump.
The motor comes off next. Unplug the electrical connector from the motor and two wires from the capacitor. Remove the two screws holding the clamps in place and then pop off the two clamps. You will need to hold up the motor with one hand while you remove the clamps or it will fall to the floor once the clamps are removed.
One piece of the coupling assemble will be attached to the motor and the other will be attached to the gearcase drive shaft. If you want to clean up the mess created by the shredded rubber center piece of the coupling assembly you will have to take off the motor mounting plate. It is held on by two bolts and removing it makes installing the coupling easier but probably not necessary.
Push the back half of the coupling on to the gearcase drive shaft until the shaft is flush with the face of the coupling. Install the new rubber center piece on to the coupling then re-install the motor mounting plate. Install the other half of the coupling on to the motor shaft and lift the motor up to the coupling. You have to rotate the motor shaft by spinning the fan blades until the coupling lines up so you can slide it into the other half of the coupling. Then just reattach the motor, connectors and water pump in the reverse order of disassembly. Read more...
PartSelect Number PS1485646
Manufacturer Part Number 285753A
This direct drive motor coupling (Direct Drive Washer Motor Coupling, Motor Coupling, Washer Motor Coupling, Coupling Kit) provides a cushioned connection between the transmission and the motor shaft. It attaches to the direct-drive transmission and the motor shaft. If this part is defective it will affect the agitator in your washer because of its direct connection with the motor. Your washer may not agitate, spin slowly, or not spin at all. The coupling must be replaced when there is no longer a consistent connection between the transmission and the motor shaft. The coupling can wear over time because of its location between two major parts of the dryer. It is subject to material fatigue over time from normal use, or breakage caused by frequent overloading. The part measures approximately 2 inches in diameter, and is constructed of plastic and metal. This model comes in black/white.
Fixes these symptoms
- Burning smell
- Leaking
- Noisy
- See more...
Installation Instructions
Jeff from Wayne, NJ
No movement from Basket & agitator
The job looked intimidating but turned out to be very easy.First take off the water pump by removing the two clips that hold it in place. Place a shallow pan under the pump to catch the water that is in the pump and hoses. Open the hose clamps with a pair of pliers or channel locks (better) and slide the hoses off of the water pump.
The motor comes off next. Unplug the electrical connector from the motor and two wires from the capacitor. Remove the two screws holding the clamps in place and then pop off the two clamps. You will need to hold up the motor with one hand while you remove the clamps or it will fall to the floor once the clamps are removed.
One piece of the coupling assemble will be attached to the motor and the other will be attached to the gearcase drive shaft. If you want to clean up the mess created by the shredded rubber center piece of the coupling assembly you will have to take off the motor mounting plate. It is held on by two bolts and removing it makes installing the coupling easier but probably not necessary.
Push the back half of the coupling on to the gearcase drive shaft until the shaft is flush with the face of the coupling. Install the new rubber center piece on to the coupling then re-install the motor mounting plate. Install the other half of the coupling on to the motor shaft and lift the motor up to the coupling. You have to rotate the motor shaft by spinning the fan blades until the coupling lines up so you can slide it into the other half of the coupling. Then just reattach the motor, connectors and water pump in the reverse order of disassembly. Read more...
Your Price
$18.20
In Stock
General Electric Washer Dryer Combo Push-to-Start Switch
PartSelect Number PS3487190
Manufacturer Part Number WE4M416
This switch is used to activate the dryer.
Fixes these symptoms
- Touchpad does not respond
- Will Not Start
- Won’t Start
- See more...
Installation Instructions
Gary from LAVALLETTE, NJ
replaced start button and start switch
disconnect power plug unscrew 3 screws in back. lean forward remove button disconnect 2 wires in back of switch. put switch connect 2 wires and button. connect 3 screws in the back. ready to start working
Read more...
Your Price
$70.91
In Stock
General Electric Washer Dryer Combo Door Handle
PartSelect Number PS12743305
Manufacturer Part Number WE01X30378
This is a door handle made for use with dryers. This door handle is made of solid white plastic and allows you to open and close the door of the dryer. If your current dryer door handle is broken or missing, it will need to be replaced. This handle measures 9 inches long and 2 inches thick and attaches at its top and base. To replace this handle, simply pry off its left side and pull it off, and then insert the prongs on the right side into the door and push it in place. This OEM door handle is sold on its own and does not come with any other accessories.
Fixes these symptoms
- Door won’t close
- See more...
Installation Instructions
TERESA from IRONDALE, AL
dryer handle broke off
once the part arrived, it was a perfect fit and just snapped on! DONE!
Read more...
Your Price
$53.90
In Stock
General Electric Washer Dryer Combo GRID ASM
PartSelect Number PS16762559
Manufacturer Part Number WE22X35337
This is a replacement lint filter slide for your dryer. It is approximately 14 inches long and 5 inches wide. It is made of white plastic and is sold individually. The slide mounts to your dryer and allows the lint filter to slide out for cleaning. If your lint filter will not slide out properly, you may need to replace the slide. This part is an authentic OEM part sourced directly from the manufacturer.
Installation Instructions
Joel from LAKE WORTH, FL
Probably due to age and heat of the dryer,the top of the slide broke.
I removed the old slide and clipped in the new one. No tools involved.
Read more...
Your Price
$20.35
In Stock
General Electric Washer Dryer Combo CONTROL KNOB
PartSelect Number PS16226089
Manufacturer Part Number WE01X30638
This control knob is a genuine OEM replacement part that is used in washer-dryer combos. It is a turn-style knob, and it comes in a dark gray color. It is typically located on the front panel of the unit and allows users to choose the wash and dry cycles, adjust temperature settings, set the timer, and activate special features such as extra rinse or delicate cycle. Over time, the knob may become damaged, worn out or no longer able to remain attached to the mounting shaft. If you have difficulty turning the knob or notice that it is unresponsive then the knob is likely faulty and will need to be replaced.
Your Price
$105.10
In Stock
General Electric Washer Dryer Combo Lid Lock & Switch Assembly
PartSelect Number PS3496878
Manufacturer Part Number WH44X10288
The door latch lid lock is to lock the door on your washer when the appliance is in use. Your washer will not start if your door is not locked. If your latch is broken, you may not be able to start a cycle or open your washer door. It is mostly black in color and made of plastic. This part measures approximately 3.75 by 3.5 inches.
Fixes these symptoms
- Lid or door won’t close
- Will Not Start
- See more...
Installation Instructions
Randy from CANTON, NC
Washer would not spin or drain
I went to You tube sight to see how I can remove front of washer so I could inspect inside and see if the problem was visible. A butter knife easily released the tabs that hold the front of washer on. My wife in the mean time found a you tube video that showed the same problem and I ordered the part right away. It showed just two screws and a plug that had to be removed. I always buy my parts from part-select because the quality and speedy delivery and tracking is great! This was an easy fix!
Read more...
Your Price
$15.84
In Stock
General Electric Washer Dryer Combo BELT DRIVE
PartSelect Number PS12342956
Manufacturer Part Number WE12X27300
Fixes these symptoms
- Spinning Issues
- Will not agitate
- See more...
Installation Instructions
Thomas from RICHMOND, CA
Socks dropping outside of the drum into the bottom caused the drive belt to come off.
I put the old belt back on but it came off after a couple of washing. I had ordered a new one. Trouble was the new belt would work its way off the large smooth wheel as I turned the motor pully to get the belt on. Solution: I taped up a stack of shims to fit between the washer bottom and the back, bottom of the smooth, drum wheel. This stopped the drive belt from rotating off as I turned the motor pully. Success. You're laying on your side, on the floor, with minimum room under the drum and lots of sharp edges.
Read more...
Your Price
$28.23
In Stock
General Electric Washer Dryer Combo SHAFT & BRACKET Assembly
PartSelect Number PS2355941
Manufacturer Part Number WE3M33
Fixes these symptoms
- Noisy
- See more...
Your Price
$40.72
In Stock
General Electric Washer Dryer Combo FILTER LINT
PartSelect Number PS11774537
Manufacturer Part Number WE18X25102
This lint filter, also referred to as a lint screen, is specially designed for various models of dryers and washer/dryer combos. It is responsible for capturing lint and debris from clothing during the drying cycle and preventing it from clogging the dryer vent. If the filter is damaged and no longer able to carry out this function you may notice longer dryer times, overheating, and excessive lint build up in the dryer vent, which creates the risk of a fire hazard. Regular cleaning and maintenance of the lint filter are essential to keep the dryer operating efficiently and safely. It is recommended to clean the filter after every use.
General Electric Washer Dryer Combo Appliance Types
Related General Electric Washer Dryer Combo Parts
- General Electric Washer Dryer Combo Drums and Tubs
- General Electric Washer Dryer Combo Switches
- General Electric Washer Dryer Combo Knobs
- General Electric Washer Dryer Combo Seals and Gaskets
- General Electric Washer Dryer Combo Hardware
- General Electric Washer Dryer Combo Thermostats
Popular General Electric Washer Dryer Combo Models
Below are the most popular General Electric Washer Dryer Combo models we have. Enter your model number in the search box to find your model.
- WSM2700DAWWW
- GUD27ESSM1WW
- GUD27ESSJ0WW LAUNDRY CENTER
- GTUP270EM1WW
- GUD24ESSM1WW
- GTUP240EM1WW
- GTUP270EM4WW
- GUD24ESSJ0WW HOME LAUNDRY COMBO
- GUD27ESSJ1WW LAUNDRY CENTER
- WSM2420D3WW
- WSM2700HBWWW
- GUD27ESPM1DG
- GTUP270EM0WW
- GTUN275EM1WW
- GTUP240EM5WW
- WSM2700WCWWW
- WSM2420TCAWW
- GTUP270GM1WW
- WSM2700HAWWW
- GTUP270EM5WW HOME LAUNDRY COMBO
