Kenmore Microwave Oven Combo Parts
- Search your model number to find:
- Genuine OEM parts guaranteed to fit
- Free manuals and guides
- Repair instructions and videos
Popular Kenmore Microwave Oven Combo Parts
Your Price
$72.96
In Stock
Kenmore Microwave Oven Combo Bake Element - 2600W 240V
. Read more...
PartSelect Number PS11740695
Manufacturer Part Number WP308180
The bake element in your oven is the part that provides heat when cooking. If your oven is too hot, or not hot enough, or does not heat evenly, you may need to replace the bake element. This part is 2600 Watts and 240 Volts. It is a closed hinged style bake element which is 15-3/4 inches long and 16-5/8 inches wide. The terminal depth is three inches and they are 1-3/4 inches apart. This part is made of metal and is black in color. Be sure to disconnect power to the oven before completing this repair.
Fixes these symptoms
- Element will not heat
- Little to no heat when baking
- Oven is too hot
- See more...
Installation Instructions
Joe from Greeley, CO
oven wouldn't heat
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires, then removed element and replaced with new. Read more...
Your Price
$12.25
In Stock
Kenmore Microwave Oven Combo FILTER,GREASE
PartSelect Number PS12713651
Manufacturer Part Number 5230W1A012E
This is a single grease filter manufactured for a microwave. The microwave grease filter filters the exhaust air and traps any grease flowing out of the appliance. It is important to keep the filter clean and intact by cleaning it regularly and replacing it when needed. A clogged air filter can cause your appliance to run inefficiently and possibly alter the taste and smell of your food. This filter is approximately 7.5 inches wide and 5 inches deep. This part is sold separately. No tools are required for this repair, the filter simply slides in and out using the easy-pull tab on the filter.
Installation Instructions
David from Smithfield, VA
Grill Vent Broken Tabs
Piece of cake. Grill arrived quickly, was easily installed with a Phillips head screwdriver, needed for the two upper screws which most folks don't think about - Hence the need for this part, since the charcoal filter is behind the grill and most people don't think about replacing this. Easy installation of all filters. Thanks!
Read more...
Your Price
$54.65
In Stock
Kenmore Microwave Oven Combo Vent Grille - Black
PartSelect Number PS3535252
Manufacturer Part Number MDX61912701
This is replacement vent grille or vent grill for your microwave. You will find the grill vent either above or below the microwave door, depending on your model. If your vent grill is discolored or cracked, or if the mounting brackets for the grill are broken, you may need to replace the grill. This part is made of black plastic and is approximately 24 inches long and 3.5 inches wide. This product is sold individually.
Fixes these symptoms
- Door not closing properly
- See more...
Installation Instructions
Andy from PERRYSBURG, OH
Vent Grille tabs snapped off
Repair was easy but you have to remove the screw at the top of the microwave (top left) in order to secure the far left tab with the hole in the tab. Place the grille in place, push to the left and then secure the screw you removed. Just remember that the mounted screw will need to be removed the next time you need access in order to replace the charcoal filter.
Read more...
Your Price
$10.58
In Stock
Kenmore Microwave Oven Combo FUSE
First off, UNPLUG THE MICROWAVE.
The fuse is located under the plastic grill at the top of the microwave. It's held on by two screws. Once you've removed the screws and taken off the plastic grill, you go to the right side of the microwave and remove another screw that holds a small metal grill in place. Removing the small metal grill is probably the toughest part of this repair. You kind of have to rock it back and forth a bit to get it to release. Once that's off, you can get to the fuse. I removed the burnt out one with a pair of needle nose pliers. I also put a small piece of cardboard under the fuse when I did this so I didn't accidentally drop it into the innards of the microwave. I did the same thing when I replaced the new fuse. I then plugged the appliance back in and made sure it worked. Once that was confirmed, I replaced both grills. Read more...
PartSelect Number PS1481237
Manufacturer Part Number WB27X10928
This ceramic microwave fuse is just over an inch in length. It is white in the center, and metal on both ends. This is a 20-amp fuse, and is used to power your microwave. If the touch pad on the microwave becomes unresponsive, the microwave produces little to no heat, or the appliance simply does not turn on, it could mean that your fuse is at fault and needs to be replaced. Because this part contains an electrical charge, remember to disconnect power to the microwave unit before you begin this repair.
NOTE: Before you start this repair, ensure that the microwave is unplugged, and the capacitor is discharged. A capacitor stores large amounts of electricity even after your microwave is unplugged.
Fixes these symptoms
- No heat
- Touchpad does not respond
- Won’t turn on
- See more...
Installation Instructions
Kim from Cliffside Park, NJ
Microwave completely stopped working
Turned out the issue was easily solved by replacing a single, inexpensive fuse. First off, UNPLUG THE MICROWAVE.
The fuse is located under the plastic grill at the top of the microwave. It's held on by two screws. Once you've removed the screws and taken off the plastic grill, you go to the right side of the microwave and remove another screw that holds a small metal grill in place. Removing the small metal grill is probably the toughest part of this repair. You kind of have to rock it back and forth a bit to get it to release. Once that's off, you can get to the fuse. I removed the burnt out one with a pair of needle nose pliers. I also put a small piece of cardboard under the fuse when I did this so I didn't accidentally drop it into the innards of the microwave. I did the same thing when I replaced the new fuse. I then plugged the appliance back in and made sure it worked. Once that was confirmed, I replaced both grills. Read more...
Your Price
$41.90
In Stock
Kenmore Microwave Oven Combo Charcoal Filter
PartSelect Number PS3527523
Manufacturer Part Number 5230W1A003A
This is an authentic LG charcoal filter for your microwave, sourced directly from the manufacturer. It is designed to remove odors from the air that circulate through your microwave vent. It measures approximately 11 inches in length, and 2.5 inches in width.
Installation Instructions
George from FALL RIVER, MA
Loss of controls and no heat.
Assisted experienced and knowledgeable local repair shop technician. Had no issues during repairs. Microwave worked properly after repairs were completed.
Read more...
Your Price
$36.68
In Stock
Kenmore Microwave Oven Combo Oven Sensor
PartSelect Number PS236398
Manufacturer Part Number WB23T10015
The function of the oven sensor is to detect the temperature within the oven cavity. If you notice that the oven is too hot or too cold, or it is not heating evenly, you may need to replace the oven sensor. The oven sensor is typically located in the back of the oven so you will most likely need to pull your oven out to access it. Many of our customers have rated this repair as easy. You will need a Phillips screwdriver to complete this repair. Be sure to disconnect the power source and shut off the gas valve before doing this repair.
Fixes these symptoms
- Element will not heat
- Little to no heat when baking
- Oven is too hot
- See more...
Installation Instructions
Sean from Highlands Ranch, CO
Oven was not coming up to temperature
I had to remove the oven from the wall because the sensor plug connction is behind the unit. Two screws hold the sensor inside the oven and then I disconnected the lead and pulled the sensor out from the front. I installed the new sensor, tightened the two screws holding it in and connected the lead. Then reinstalled the oven into the wall. Overall, a very easy repair once you get the oven out.
Read more...
Your Price
$45.34
In Stock
Kenmore Microwave Oven Combo Secondary Door Switch
PartSelect Number PS237421
Manufacturer Part Number WB24X829
The secondary door switch is a simple on/off mechanism that stops the microwave from operating when the door is open (normally opened). The switch monitors the door latch position, and communicates whether the door is open or closed to the electrical control board. This door switch is approximately 1 inch long, and has 2 metal prongs called terminals that extend out of its body. Common symptoms related to a faulty secondary door switch include: microwave will not turn/shut off, or the microwave will not heat properly.
NOTE: Before you begin this repair, first make sure your microwave is unplugged, and that your capacitor is discharged. A capacitor stores large amounts of electricity even when your microwave is unplugged.
Fixes these symptoms
- Doesn’t shut off
- No heat
- Touchpad does not respond
- See more...
Installation Instructions
Marla from Arlington, TX
light worked, timer and control pad worked, but no turntable, no heat, no noises of any sort, just didn't start up
Noted on partselect.com that someone else with this problem, found it to be secondary door switch. There are three door switches in this model, but online info noted that one of the three might feel "soft" (in my case, one switch clicked in a rather "jiggly" way, the other two were strong decisive clicks.) To access the door switches on this model was the only difficult part. First use a torx bit to remove the two torx screws below the latches inside the microwave. This frees the latching part inside, that holds the door switches, which you will remove after you take off the control panel. The top grill has to come off before you can remove the door panel. Remove the screws above the grill, on the microwave top cover, The grill on this model is covered with a panel that moves out when it vents. After removing the two top screws, the covered grill vent slides left to remove. Be careful, as the sliding tabs are plastic. Wiggle and jiggle it, to slip it off. Below the removed grill, is a small metal grill with one screw in lower center. Remove that screw, and wiggle that out. You'll then see the one screw that holds on the control panel. Remove this screw, and lift the control panel up to remove. Again, go slowly and gently, as the bottom tabs holding the control panel in, are also plastic and easily broken. Lay the control panel on something, (I used the coffee maker) and pull out the wire bundles tucked on the left, that are attached to the latching panel. Wiggle the latching panel gently to lift it up off of it's plastic tabs and pull it out towards you, so you can see the three door switches. Each switch (part number WB24X829) has a little black switch on it. Feel each switch with either your finger, or a screwdriver to see which one doesn't "click" strongly. The weak one is the one you will replace. The door switches are fitted into a tab, and plugged into their wires. Remove the defective switch, pull out the wires, and replace it with the new switch, plugging back the wires, and slipping it back into it's plastic tabs. Then put everything back together in reverse order. The entire job took me fifteen minutes EXCEPT for figuring out how to slide off the upper grill, which I have told you. A repairman would have cost $150, the part was $18. AND, there's a good chance, the other two switches will get "used up" in the next year or so as well, so I'll be ready next time. Thank you, Partselect, why work all day, to make money, only to give it to somebody else, for fifteen minutes of work. All I needed was the knowledge.
Read more...
Your Price
$56.73
In Stock
Kenmore Microwave Oven Combo Meat Probe Thermistor
PartSelect Number PS1481046
Manufacturer Part Number WB20T10024
This probe is used to check the internal temperature of the meat to ensure proper temperature is reached. Also known as a Meat Probe.
Fixes these symptoms
- Will not program
- See more...
Installation Instructions
Eric from SOUTHBURY, CT
Temp probe was defective
Threw the old one out - plugged the new one in. Steak came out just as ordered - medium rare.
Read more...
Your Price
$8.17
In Stock
Kenmore Microwave Oven Combo Locker
PartSelect Number PS3522838
Manufacturer Part Number 4026W2A019A
The locker, or door latch assembly fits to the inside of the microwave door, and keeps the door closed. If the door on your microwave oven doesn’t appear to close properly, you may have a problem with the door latch assembly. This locker is made of plastic and measures 7 inches long x 2 inches wide. If either of the hooks is broken or does not have any spring tension, you may need to replace the assembly.
Fixes these symptoms
- Door not closing properly
- See more...
Installation Instructions
Christine from LUXEMBURG, WI
The over the stove microwave door would not close.
I unplugged the microwave. I did watch a YouTube video to see how the plastic frame around the door could be removed. I used a putty knife to pry it off. The spring was still in good shape, so I hooked it up to the new latch/locker part and onto the microwave. This was just a little time consuming because I was trying to be careful so I wouldn't break anything on the new part. The plastic frame clicked right back on. I plugged the microwave in and it worked right away. If I can do it, you can do it. Sure beat buying a new microwave. Great experience.
Read more...
Your Price
$14.37
In Stock
Kenmore Microwave Oven Combo FILTER,CHARCOAL
PartSelect Number PS12713650
Manufacturer Part Number 5230W1A011E
This is the replacement charcoal filter for your microwave. It is approximately 8 inches by 5 inches. The charcoal filter removes cooking odors from the air that circulate through the microwave vent. You will likely need to replace the charcoal filter if you notice any damage to it, or if it has been in your microwave for a long time. This part is sold individually and is an authentic OEM part sourced directly from the manufacturer.
Installation Instructions
David from Smithfield, VA
Grill Vent Broken Tabs
Piece of cake. Grill arrived quickly, was easily installed with a Phillips head screwdriver, needed for the two upper screws which most folks don't think about - Hence the need for this part, since the charcoal filter is behind the grill and most people don't think about replacing this. Easy installation of all filters. Thanks!
Read more...
Kenmore Microwave Oven Combo Appliance Types
Related Kenmore Microwave Oven Combo Parts
- Kenmore Microwave Oven Combo Elements and Burners
- Kenmore Microwave Oven Combo Lights and Bulbs
- Kenmore Microwave Oven Combo Sensors
- Kenmore Microwave Oven Combo Hardware
- Kenmore Microwave Oven Combo Switches
- Kenmore Microwave Oven Combo Fuses
- Kenmore Microwave Oven Combo Thermostats
- Kenmore Microwave Oven Combo Racks
- Kenmore Microwave Oven Combo Hinges
- Kenmore Microwave Oven Combo Brackets and Flanges
- Kenmore Microwave Oven Combo Doors
- Kenmore Microwave Oven Combo Seals and Gaskets
- Kenmore Microwave Oven Combo Ducts and Vents
- Kenmore Microwave Oven Combo Springs and Shock Absorbers
- Kenmore Microwave Oven Combo Drawers and Glides
- Kenmore Microwave Oven Combo Motors
Popular Kenmore Microwave Oven Combo Models
Below are the most popular Kenmore Microwave Oven Combo models we have. Enter your model number in the search box to find your model.
- 72185033010
- 72185039010
- 72180042700
- 72185032010
- 72180049700
- 72179203010
- 72166339800
- 91147813202
- 9114942592
- 72179209010
- 91147793202
- 72180044700
- 72180832500
- 9114942993
- 91147862100
- 72180839500
- 91141479791
- 72179202010
- 79048903000 Kenmore Oven/Microwave Combo Model 790.48903000 (79048903000, 790 48903000) Parts
- 91141489890
