Official KitchenAid Washer Dryer Combo Parts

Videos!

Direct Drive Motor Coupling – Part Number: 285753A

Your Price

$27.87

KitchenAid Washer Dryer Combo Direct Drive Motor Coupling

★★★★★

160 Reviews

PartSelect Number PS1485646

Manufacturer Part Number 285753A

This direct drive motor coupling (Direct Drive Washer Motor Coupling, Motor Coupling, Washer Motor Coupling, Coupling Kit) provides a cushioned connection between the transmission and the motor shaft. It attaches to the direct-drive transmission and the motor shaft. If this part is defective it will affect the agitator in your washer because of its direct connection with the motor. Your washer may not agitate, spin slowly, or not spin at all. The coupling must be replaced when there is no longer a consistent connection between the transmission and the motor shaft. The coupling can wear over time because of its location between two major parts of the dryer. It is subject to material fatigue over time from normal use, or breakage caused by frequent overloading. The part measures approximately 2 inches in diameter, and is constructed of plastic and metal. This model comes in black/white.

Fixes these symptoms

Burning smell
Leaking
Noisy
See more...

Installation Instructions

Jeff from Wayne, NJ

No movement from Basket & agitator

The job looked intimidating but turned out to be very easy.
First take off the water pump by removing the two clips that hold it in place. Place a shallow pan under the pump to catch the water that is in the pump and hoses. Open the hose clamps with a pair of pliers or channel locks (better) and slide the hoses off of the water pump.
The motor comes off next. Unplug the electrical connector from the motor and two wires from the capacitor. Remove the two screws holding the clamps in place and then pop off the two clamps. You will need to hold up the motor with one hand while you remove the clamps or it will fall to the floor once the clamps are removed.
One piece of the coupling assemble will be attached to the motor and the other will be attached to the gearcase drive shaft. If you want to clean up the mess created by the shredded rubber center piece of the coupling assembly you will have to take off the motor mounting plate. It is held on by two bolts and removing it makes installing the coupling easier but probably not necessary.
Push the back half of the coupling on to the gearcase drive shaft until the shaft is flush with the face of the coupling. Install the new rubber center piece on to the coupling then re-install the motor mounting plate. Install the other half of the coupling on to the motor shaft and lift the motor up to the coupling. You have to rotate the motor shaft by spinning the fan blades until the coupling lines up so you can slide it into the other half of the coupling. Then just reattach the motor, connectors and water pump in the reverse order of disassembly. Read more...

Videos!

Your Price

$27.58

KitchenAid Washer Dryer Combo Clutch Assembly

★★★★★

78 Reviews

PartSelect Number PS334641

Manufacturer Part Number 285785

A clutch assembly (Clutch, Washer Clutch) is found in your washing machine and is responsible for spinning the basket during the spin cycle. The clutch lining can wear over time. If the clutch lining is worn out, the clutch assembly will not rotate properly to release the brake. If you notice a burning smell, or the machine shaking and moving more than normal, this could indicate there is an issue with your clutch. If the washer spins when the washer basket is empty but not when it’s full, or if the assembly begins to turn blue, you may need to replace the clutch assembly. This assembly includes a brake cam driver, blue springs for large capacity washers, a black spring for compact washers, and the installation instructions. It’s constructed of plastic and metal, and comes in beige/silver.

Fixes these symptoms

Burning smell
Spinning Issues
Spins slowly
See more...

Installation Instructions

Andrew from SLC, UT

spin cycle did not engage

researched potential causes, found cluch dust under the washer and determined that it wouldn't engage because clutch was too worn. ordered the assembly, removed agitator from inside the tub as it is connected to the gear shaft, turned washer on it's back for access to motor, unattached the direct drive water pump from the motor drive, unbolted the 3 gearcase mounting bolts and took the entire gearcase, shaft, motor, etc... together, out from under the washtub. the clutch slides off the gearshaft with a little fidgeting and the new assembly is easily installed where the previous was. put everything back together... then... spin spin! worked perfectly Read more...

Videos!

Your Price

$7.04

KitchenAid Washer Dryer Combo Tub Spring

★★★★★

18 Reviews

PartSelect Number PS11751118

Manufacturer Part Number WPW10250667

This tub spring is also known as suspension spring, balance spring, or counterweight spring. It is sold individually. The function of the part is to counterbalance the weight of the motor on the front of the front-load washer so the washer tub sits straight and even during the spin cycle. You may need to replace the spring if tub is sitting tilted forward. A broken spring will result in the tub being off-balance during the spin cycle which can cause further damage to washer parts. It is recommended to check all suspension springs as they often wear at the same rate. Tools needed for repair are a Phillips screw driver, flat blade screw driver, and a pair of pliers.

Fixes these symptoms

Leaking
Shaking and Moving
Spinning Issues
See more...

Installation Instructions

RICHARD from PHILA, PA

Replace Water Pump Coupling

Removed casing tip over washer disconnected water pump. Disconnected motor then replace coupling then reassemble motor then replaced water pump. Read more...

Videos!

Water Inlet Valve with Mounting Bracket – Part Number: 285805

Your Price

$35.28

KitchenAid Washer Dryer Combo Water Inlet Valve with Mounting Bracket

★★★★★

132 Reviews

PartSelect Number PS334646

Manufacturer Part Number 285805

The water inlet valve on your washing machine is used to fill the tub with cold, warm, or hot water for the wash and rinse cycles. This part could have either a blue or green-colored valve body. There are two ports for water to enter and this valve is compatible with a half-inch ID hose. It has two 3/4-11x1/2 NHT hose threads. You may have a faulty valve if your washer is leaking, has no hot or cold water, will not stop filling with water, will not fill with water, fills and drains at the same time, or is noisy. To confirm that the valve is faulty, unplug the washer when the symptom occurs. If the washer continues to fill, then the inlet valve is defective.

Fixes these symptoms

Leaking
No hot or cold water
Water Filling Issues
See more...

Installation Instructions

Don from Wyoming, MN

Washer stopped at rinse cycle

Removed the top and back panels. Replaced
compoments and reassembled.
Test run machine. Ran like new! Read more...

Videos!

Dryer Lint Filter and Cover – Part Number: W10828351

Your Price

$54.44

KitchenAid Washer Dryer Combo Dryer Lint Filter and Cover

★★★★★

48 Reviews

PartSelect Number PS11726200

Manufacturer Part Number W10828351

Cover and filter as an assembly. It is used in dryer, If the lint filter cover is damaged or cracked, it should be replaced.

Fixes these symptoms

Marks left on clothes
Noisy
See more...

Installation Instructions

Kevin from Seattle, WA

lint filter screen was broken

replace lint filter with new part. Great service and quick delivery! Thanks! Read more...

Videos!

Heating Element Connection Wire Kit – Part Number: 279457

Your Price

$11.06

KitchenAid Washer Dryer Combo Heating Element Connection Wire Kit

★★★★★

3 Reviews

PartSelect Number PS334206

Manufacturer Part Number 279457

This kit is used for electric clothes dryers, and it comes with a yellow wire nut.

Fixes these symptoms

Not Heating
See more...

Installation Instructions

Christopher from dublin, OH

no heat

took a couple differant parts to fix the dryer. i ordered one part at a time. i was expecting to wait the 5 days for shipping but i got home from work the next day of odering parts and they were there waiting for me on my doorstep. all three times i ordered. this website is the best site to order parts. i wont go to another website or store if i need to order parts for appliances. u guys have my business for life. thumbs up. Read more...

Single Front Panel Cip – Part Number: W10854425

Your Price

$16.46

KitchenAid Washer Dryer Combo Single Front Panel Cip

★★★★★

3 Reviews

PartSelect Number PS11731288

Manufacturer Part Number W10854425

This part is the replacement single front panel clip for your dryer. It is made of metal and is approximately 2 inches long and ¾ inch wide. The front panel retainer clip is what holds the front panel on to the dryer. If the clip is damaged or missing, or if the front panel appears loose, you may need to replace the clip. This part is sold individually and is an authentic OEM part.

Fixes these symptoms

Noisy
See more...

Installation Instructions

Sean from BAR NUNN, WY

Belt was slipping, and having a hard time spinning the drum

First off, start by turning of the breaker to the dryer and confirming the power has been turned off. Next, remove the lint screen and two screws holding the lint screen housing to the lid. Remove the two side moldings on the control panel and the two screws holding doun the enclosure. Slide the control enclosure forward and lift up . Take a picture of the wiring for later reference and carefully unplug the wires and set the enclosure aside. Next, remove the two screws holding the rear lid retaining clips. Gently pry up on the front of the lid to realese hold doun clips, swing the lid up and remove it from the rear clips, set the lid aside. Remove the two screws on corners of front cover located near the top, unplug the door switch. Remove the front cover by lifting straight up, set aside. Now remove the belt from the motor by realeasing the tensioner and remove it from the drum. You can now remove the drum through the front. Now is a good time to check the condition of your drum rollers, clean them as needed or replace them. Clean the roller shafts and apply a quality grease. "Clean the roller groove on the drum" this is what makes the drum sound bumpy! Remove the rear seal and replace it as per the instructions that come with the seal. The glue dries quickly, so have the seal fully in place and apply glue to small areas replacing the seal fully before moving on. You can now reinstall the drum being careful not to damage the seal. Place the drum on the rollers, reach inside and work the seal into place. You can now replace the belt and work in reverse with the casings! It took me longer to type these instructions than it did to make this repair! Enjoy your like new machine! Read more...

Videos!

Your Price

$9.76

KitchenAid Washer Dryer Combo Door Catch

★★★★★

3 Reviews

PartSelect Number PS11741434

Manufacturer Part Number WP3389441

This white female door catch is attached to the dryer door.

Fixes these symptoms

Door Pops Open
Door won’t close
See more...

Installation Instructions

tony from prineville, OR

Top door catch assembly had broken

It was so easy, that my wife did it the day we got the part before I got home from work. She wedged it out with a flat head screw driver and then pushed the new door catch assembly in with her thumb. Pretty simple, thanks for having parts like this available to the public! Read more...

Videos!