MTD Lawn Mower Parts

Grass Catcher Frame – Part Number: 647-04271-0637

Your Price

$37.15

MTD Lawn Mower Grass Catcher Frame

★★★★★

1 Review

PartSelect Number PS9988561

Manufacturer Part Number 647-04271-0637

Rear Axle Assembly – Part Number: 911-04144B

Your Price

$33.18

MTD Lawn Mower Rear Axle Assembly

★★★★★

2 Reviews

PartSelect Number PS10023414

Manufacturer Part Number 911-04144B

Axle assembly attaches the rear wheels to the mower and allows the wheels to rotate. This part replaces part numbers 911-04144 and 911-04144A. Wear work gloves to protect your hands when installing this part.

Bolt- Stud - H=42.5mm – Part Number: 90043-ZL8-000

Your Price

$4.99

MTD Lawn Mower Bolt- Stud - H=42.5mm

PartSelect Number PS10021937

Manufacturer Part Number 90043-ZL8-000

Nut, Flange Lock, 5/16-18, Grf – Part Number: 712-04063

Your Price

$3.99

MTD Lawn Mower Nut, Flange Lock, 5/16-18, Grf

PartSelect Number PS9092936

Manufacturer Part Number 712-04063

This nut is a manufacturer-approved replacement part for various lawn and garden equipment. It is sold individually, not as part of a kit or assembly. Also referred to as a Lock Nut, it is resistant to loosening when threaded on a bolt. It has a variety of applications and is used in multiple locations on most models. Please refer to your owners manual to determine the exact location. While made of durable metal, the ends can round off from improper use of a wrench or socket. Depending on the location, this part may also become worn through regular use of your machine. It should be replaced when visibly cracked, worn or damaged. To complete this repair, you will need a wrench or socket, and a torque wrench. Ensure you torque the bolt according to the manufacturer recommendations. Customers rate this repair as Easy.

Hex Wash. Scr. 1/4-14 x .625" Lg. – Part Number: 710-0896

Your Price

$4.99

MTD Lawn Mower Hex Wash. Scr. 1/4-14 x .625" Lg.

PartSelect Number PS10001824

Manufacturer Part Number 710-0896

Installation Instructions

Laurie from RICHLANDS, NC

Oil Drain Sleeve

I wish this was longer...it's only about 6", barely enough to have the oil flow past the metal plate of the riding lawnmower. I'm going to figure out a way to make a permanent extension something like this video would be SO much better https://www.youtube.com/watch?v=G9ZVoeqr6R8&t=79s Read more...

Element- Air Cleaner – Part Number: 17211-ZL8-023

Your Price

$7.06

MTD Lawn Mower Element- Air Cleaner

PartSelect Number PS9903219

Manufacturer Part Number 17211-ZL8-023

This air cleaner element, also known as an air filter, is found in your lawn equipment. Typically housed in a rectangular container, it is located near the air intake area or carburetor of your machine. It keeps dust, dirt, and debris from entering the combustion chamber. If it is clogged, the restricted airflow will make the engine misfire or run poorly, and potentially cause an engine failure. To replace the element, you will need to remove its housing cover by unscrewing or unclipping it. This OEM-certified filter is sold individually.

Installation Instructions

Merle from ROCKFORD, MI

no problen

Very easy to install, pushed the hinge clips in the slots and bent the trail shield a little to hook into the clips. This old mower looks like new again. Runs like new also. Read more...

Your Price

$3.99

MTD Lawn Mower Hinge Clip

PartSelect Number PS10006072

Manufacturer Part Number 732-04631A

Grass Bag, Black – Part Number: 764-04077D

Your Price

$43.58

MTD Lawn Mower Grass Bag, Black

★★★★★

4 Reviews

PartSelect Number PS17016671

Manufacturer Part Number 764-04077D

Grass Bag, Black

Installation Instructions

Mark from PHOENIX, AZ

Replaced existing grass bag

The bag was slightly larger than the original. So the clips along all sides needed to be trimmed slightly to fit the existing frame. 15 minute fix and it works perfect. Read more...

Cable Barrel Holder – Part Number: 946-0605

Your Price

$4.99

MTD Lawn Mower Cable Barrel Holder

★★★★★

1 Review

PartSelect Number PS9167431

Manufacturer Part Number 946-0605

This cable barrel holder is a genuine OEM part that is designed for use with tillers and snow throwers. Sold as an individual part, this holder measures approximately 1-inch in length and is used to secure the clutch control handle and cable together. This holder is made of durable plastic and can replace the old holder by simply removing it, inserting the cable into the new holder, and tightening it until it is locked in place.?